THE PRELIMINARY RESEARCH FOR IMPLEMENTATION OF IMPROVED DTC SCHEME OF HIGH PERFORMANCE PMSM DRIVES BASED ON FPGA

Tole Sutikno

Abstract


The direct torque control (DTC) is one of control approache that is used commonly in PMSM control system. This method supports a very quick and precise torque response. However, the DTC method is not perfect and has some disadvantages. Many researchers have been proposed to modify the basic DTC scheme for PMSM drive. All this contributions allow performance to be improved, but at the same time they lead to more complex schemes. Furthermore, the PMSM drive control systems are usually based on microcontroller and DSP. Some researchers also have been used DSP and FPGA together to develop DTC for AC drives. These allow improving the performance, but they will increase cost. For the reason above, this paper proposed a new DTC scheme to apply only based on FPGA. The preliminary research showed that the proposed DTC sheme can reduce torque and flux ripples significantly. Therefore, this paper also recomend to realize proposed DTC scheme based on FPGA in order to support to execute very fast computation.The implementation is hoped that it will very potential to replace not only the induction motor but also the DC servo motor in a number of industrial process, commercial, domestic and modern military applications of high-performance drive.


Full Text:

PDF

References


. L. Wang, Y. Gao, "A Novel Strategy of Direct Torque Control for PMSM Drive Reducing Ripple in Torque and Flux," Electric Machines & Drives Conference, 2007. IEMDC '07. IEEE International, vol.1, no., pp.403-406, 3-5 May 2007.

. B. H. Bae, et al., "Implementation of sensorless vector control for super-high-speed PMSM of turbo-compressor," IEEE Trans. on Industry Applications, Vol. 39, No. 3, pp. 811-818, 2003.

. C. Bian, S. Ren, and L. Ma, “Study on Direct Torque Control of Super High-speed PMSM” IEEE International Conference on Automation and Logistics 2007, pp.2711-2715, 18-21 Aug. 2007.

. L. .Zhong, et al., “Analysis of direct torque control in permanent magnet synchronous motor drives”, IEEE Transaction on power electronics, Vol. 12, No. 3, pp. 528-536, 1997.

. G.S. Buja, and Kazmierkowski, “Direct Torque Control of PWM Inverter-Fed AC Motor-A Survey”, IEEE Transactions on Industrial Electronics, Vol.51, No.4, pp. 744-757, Aug 2004.

. I. Takahashi, and T. Noguchi, “A New Quick-Response and High-Efficiency Control Strategy of an Induction Motor”, IEEE Transactions on Industry Applications, Vol.IA-22, No.5, pp. 820-827, Sept/Oct 1986.

. M. Depenbrock, “Direct self control (DSC) of inverter-fed induction machine”, IEEE Trans. on Power Electronics 3 (4), 420–429 (1988).

. H. Nakai, H. Ohtani, and Y. Inaguma, “Novel Torque Control Technique for High Efficiency/High Power Interior Permanent Magnet Synchronous Motors”, Research Report, R&D Review of Toyota CRDL Vol. 40 No.2, pp. 44-49, Mar.17, 2005.

. M. Janaszek, “New Method of DRET-Control for PMSM”, Bulletin of The Polish Academy of Sciences, Technical Sciences, Vol.54, No.3, 2006.

. D.H. Lee, Y.J. An, and E.C. Nho, “A High Performance Direct Torque Control Scheme of Permanent Magnet Synchronous Motor”, 7th International Conference on Power Electronics and Drive Systems (PEDS '07), pp.1361-1366, 27-30 Nov. 2007.

. L. Li, et al., “A high-performance direct torque control based on DSP in permanent magnet synchronous motor drive”, Proceedings of the 4th World Congress Intelligent Control and Automation, vol.2, pp.1622-1625, 10-14 June 2002.

. Y. Xu, Y. Zhong, and H. Yang, “A Modified Direct Toque Control for Interior Permanent Magnet Synchronous Motor Drive Without a Speed Sensor”, CES/IEEE 5th International Power Electronics and Motion Control Conference, 2006 (IPEMC '06), vol. 3, pp.1-4, Aug. 2006.

. D. Rekioua, and T. Rekioua, “A new approach to direct torque control strategy with minimization torque pulsations in permanent magnets synchronous machines”, Power Tech, 2005 IEEE Russia, pp. 1-6, 27-30 June 2005.

. J. Zhang; M.F. Rahman, and C. Grantham, “A New Scheme to Direct Torque Control of Interior Permanent Magnet Synchronous Machine Drives for Constant Inverter Switching Frequency and Low Torque Ripple”, CES/IEEE 5th International Power Electronics and Motion Control Conference, 2006 (IPEMC '06), vol. 3, pp. 1-5, Aug. 2006.

. K. Gulez, A.A. Adam, and H. Pastaci, "A Novel Direct Torque Control Algorithm for IPMSM with Minimum Harmonics and Torque Ripples", IEEE/ASME Transactions on Mechatronics, vol.12, no.2, pp.223-227, April 2007.

. L. Tang. L. Zhong, M.F. Rahman and Y. Hu, “A novel direct torque control for interior permanent-magnet synchronous machine drive with low ripple in torque and flux-a speed-sensorless approach”, IEEE Transactions on Industry Applications, vol. 39, Issue 6, pp. 1748-1756, Nov.-Dec. 2003.

. L. Tang, L. Zhong, M.F. Rahman, and Y. Hu, “A novel direct torque controlled interior permanent magnet synchronous machine drive with low ripple in flux and torque and fixed switching frequency”, IEEE Transactions on Power Electronics, Issue 2, vol. 19, pp. 346–354, March 2004.

. L. Wang, and Y. Gao, “A Novel Strategy of Direct Torque Control for PMSM Drive Reducing Ripple in Torque and Flux”, IEEE International Electric Machines & Drives Conference, 2007 (IEMDC '07), vol. 1, pp. 403-406, 3-5 May 2007.

. J. Faiz, and S.H.Mohseni-Zonoozi, “A novel technique for estimation and control of stator flux of a salient-pole PMSM in DTC method based on MTPF”, IEEE Transactions on Industrial Electronics, Issue 2, vol. 50, pp. 262-271, April 2003.

. M. Fu, and L. Xu, “A sensorless direct torque control technique for permanent magnet synchronous motors”, Conference Record of the 1999 IEEE Industry Applications Conference,Thirty-Fourth IAS Annual Meeting, vol.1, pp.159-164, 3-7 Oct. 1999.

. M.E. Haque, L. Zhong, M.F. Rahman, “A sensorless speed estimator for application in a direct torque controller of an interior permanent magnet synchronous motor drive, incorporating compensation of offset error”, IEEE 33rd Annual Power Electronics Specialists Conference 2002. (PESC 02), vol. 1, pp. 276-281, 23-27 June 2002 .

. M.F. Rahman, et al., “A sensorless speed estimator for the direct torque control of an interior permanent magnet synchronous motor drive”, International Conference on Power Electronics, Machines and Drives 2002, (Conf. Publ. No. 487), pp. 504-509, 4-7 June 2002 .

. K.E.B. Quindere, E. Ruppert F. and M.E. de Oliveira F., “A Three-Level Inverter Direct Torque Control of a Permanent Magnet Synchronous Motor Industrial Electronics”, IEEE International Symposium on Industrial Electronics 2006, vol. 3, pp. 2361-2366, July 2006.

. Z. Xu, and M.F. Rahman, “Direct Torque and Flux Regulation of an IPM Synchronous Motor Drive Using Variable Structure Control Approach”, IEEE Transactions on Power Electronics, Issue 6, vol. 22, pp.2487-2498, Nov. 2007.

. L. Bao-hua, L. Wei-guo, Z. Xi-wei, and L. Rong, “Research on Direct Torque Control of Permanent Magnet Synchronous Motor Based on Optimized State Selector”, IEEE International Symposium on Industrial Electronics 2006, vol. 3, pp. 2105-2109.

. J. Luukko, and J. Pyrhonen, “Selection of the flux linkage reference in a direct torque controlled permanent magnet synchronous motor drive”, 5th International Workshop on Advanced Motion Control, 1998 (AMC '98), pp. 198-203, Coimbra, 29 June-1 July 1998.

. G. Diamantis, and J.M. Prousalidis, “Simulation of a ship propulsion system with DTC driving scheme”, Second International Conference on Power Electronics Machines and Drives 2004 (PEMD 2004), vol. 2, pp.562-567 (Conf. Publ. No. 498), 31 March-2 April 2004.

. Y. Li, and W. Liu, “Simulation Study on the Effect of Voltage Vector on Torque in Direct Torque Control System of Permanent Magnet Synchronous Motor”, 2nd IEEE Conference on Industrial Electronics and Applications 2007, pp.1521-1525, 23-25 May 2007.

. J. Mengjia, et al., “Stator flux estimation for direct torque controlled surface mounted permanent magnet synchronous motor drives over wide speed region”, Proceedings of the Eighth International Conference on Electrical Machines and Systems 2005 (ICEMS 2005), vol. 1, pp. 350-354, 27-29 Sept. 2005.

. C. Ortega, et al., “Torque ripple reduction in PMSM DTC drives using matrix converters”, European Conference on Power Electronics and Applications 2007, pp. 1–10 2-5 Sept. 2007.

. A.A. Adam, and K. Gulez, “Torque ripples and EMI noise minimizations in PMSM using hybrid filter”, SICE Annual Conference 2007, pp.2978-2983, Kagawa University, 17-20 Sept. 2007.

. M.R. Zolghadri, et al., ”A DSP based direct torque controller for permanent magnet synchronous motor drives”, 29th Annual IEEE Power Electronics Specialists Conference 1998 (PESC 98), vol. 2, pp.2055-2061, 17-22 May 1998.

. C. Yongjun, et al., “A stator resistance compensator for a direct torque controlled low speed and high torque permanent magnet synchronous motor“, 42nd International Universities Power Engineering Conference 2007 (UPEC 2007), pp.174-177, 4-6 Sept 2007.

. L. Lianbing, W. Xiaojun, and S. Hexu, “A variable-voltage direct torque control based on DSP in PM synchronous motor drive”, IEEE Region 10 Conference on Computers, Communications, Control and Power Engineering 2002 (TENCON '02), vol. 3, pp. 2065-2068, 28-31 Oct. 2002.

. C. French, and P. Acarnley, “Direct torque control of permanent magnet drives” IEEE Transactions on Industry Applications, Issue. 5 , vol. 32, pp.1080-1088, Sep/Oct 1996.

. C. French, and P. Acarnley, “Direct torque control of permanent magnet drives” Industry Applications Conference 1995 (IAS '95), Thirtieth IAS Annual Meeting, Conference Record of the 1995 IEEE, vol. 1, pp.199-206, 8-12 Oct 1995.

. D. Swierczynski, and M.P. Kazmierkowski, “Direct torque control of permanent magnet synchronous motor (PMSM) using space vector modulation (DTC-SVM)-simulation and experimental results”, IEEE 28th Annual Conference of the Industrial Electronics Society 2002 (IECON 02), vol.1, pp.751-755, 5-8 Nov. 2002.

. Y. Chen, S. Huang, and S. Wan, “Direct Torque Controller for Low Velocity and High Torque PMSM Based on TMS320F2812 DSP”, International Conference on Mechatronics and Automation 2007 (ICMA 2007), pp.3662-3667, 5-8 Aug. 2007.

. D. Swierczynski, M.P. Kazmierkowski, and F. Blaabjerg, “DSP based direct torque control of permanent magnet synchronous motor (PMSM) using space vector modulation (DTC-SVM)” IEEE International Symposium on Industrial Electronics 2002 (ISIE 2002), vol.3 pp.723-727, 26-29 May 2002.

. B. Singh, B.P. Singh, S. Dwivedi, “DSP Based Implementation of Sliding Mode Speed Controller for Direct Torque Controlled PMSM Drive”, IEEE International Conference on Industrial Technology 2006 (ICIT 2006), pp.1301-1308, 15-17 Dec. 2006.

. P. Vas, and W. Drury, “Electrical machines and drives: present and future” 8th Mediterranean Electrotechnical Conference 1996 (MELECON '96), vol.1, pp.67-74, 13-16 May 1996.

. W. Lin, “Implementation of Direct Torque Control for Permanent Magnet Synchronous Motor with Space Vector Modulation Based on DSP” 8th International Conference on Signal Processing 2006, vol.4, 16-20 July 2006.

. C.L. Toh, NRN Idris, AHM Yatim, ND Muhammad, and M. Elbuluk, “Implementation of a New Torque and Flux Controllers for Direct Torque Control (DTC) of Induction Machine Utilizing Digital Signal Processor (DSP) and Field Programmable Gate Arrays (FPGA)”, IEEE 36th Power Electronics Specialists Conference 2005 (PESC '05), pp.1594-1599, 2005.

. C.L. Toh, N.R.N. Idris, A.H.M. Yatim, and F. Patkar, “Design and Implementation of a Direct Torque Control of Induction Machine utilizing a Digital Signal Processor and the Field Programmable Gate Arrays”, International Conference on Power Electronics and Drives Systems (PEDS 2005), vol. 1, pp.72–77, 16-18 Jan 2006.

. N.R.N. Idris, T.C. Ling, M.E. Elbuluk, “New torque and flux controllers for direct torque control of induction machines”, Fourtieth IAS Annual Meeting, Conference Record of the Industry Applications Conference 2005, vol. 2, pp.979-984, 2-6 Oct. 2005.

. B.K. Bose, and P.M. Szczesny, “A microcomputer-based control and simulation of an advanced IPM synchronous machine drive system for electric vehicle propulsion”, IEEE Transactions on Industrial Electronics, Issue 4, vol.35, pp. 547-559, Nov. 1988.

. R. Wu, and G.R. Slemon, “A permanent magnet motor drive without a shaft sensor”, IEEE Transactions on Industry Applications, Issue 5, vol. 27, pp.1005-1011, Sept.-Oct. 1991.

. H.W. Park, et al., “Position sensorless speed control scheme for permanent magnet synchronous motor drives, IEEE International Symposium on Industrial Electronics 2001 (ISIE 2001), vol. 1, pp. 632–636, 12-16 June 2001.

. U. Schaible, and B. Szabados, “A torque controlled high speed flywheel energy storage system for peak power transfer in electric vehicles”, Industry Applications Society Annual Meeting 1994 (Conference Record of the 1994 IEEE), vol.1, pp.435-442, 12-6 Oct. 1994.

. R. Wu, and G.R.Slemon, “A permanent magnet motor drive without a shaft sensor”, Industry Applications Society Annual Meeting 1990. (Conference Record of the 1990 IEEE), vol.1, pp. 553-558, 7-12 Oct. 1990.

. E. Monmasson, and Y.A. Chapuis, “Contributions of FPGAs to the Control of Electrical System, a Review”, IEEE Industrial Electronic Society Newsletter, vol. 49. no. 4, pp.8-15, 2002.

. S. Ferreira, et al., “Design and prototyping of direct torque control of induction motors in FPGAs”, 16th Symposium on Integrated Circuits and Systems Design (SBCCI 2003), pp.105- 110, 8-11 Sept. 2003.

. Z. Zhou, et al., “FPGA Realization of a High-performance Servo Controller for PMSM”, in Proc. 9th IEEE Appl. Power Electron. Conf. Expo, 2004, vol.3, pp.1604-1609.

. S. Jiang, et al., “Modeling and Cosimulation of FPGA-Based SVPWM Control for PMSM”, 31st Annual Conference of IEEE Industrial Electronics Society 2005 (IECON 2005), vol. 6 pp. 76-83, 6-10 Nov. 2005

. V.D. Colli, et al., "Design of a System-on-Chip PMSM Drive Sensorless Control", IEEE International Symposium on Industrial Electronics 2007 (ISIE 2007), pp.2386-2391, 4-7 June 2007.

. E. Monmasson and M.N. Cirstea, “FPGA Design Methodology for Industrial Control - A Review”, IEEE Transcactions on Industrial Electronics, vol.54, no.4, pp. 1824-1842. August 2007.

. C.T. Kowalski, J. Lis, and T. Orlowska-Kowalska, “FPGA Implementation of DTC Control Method for the Induction Motor Drive”, The International Conference on Computer as a Tool (EUROCON 2007), pp. 1916-1921, 9-12 September 2007.

. Y.S. Kung, and M.H. Tsai, FPGA-Based Speed Control IC for PMSM Drive With Adaptive Fuzzy Control, IEEE Transaction on Power Electronics, vol.22, no.6, November 2007.

. L. Charaabi, E. Monmasson, M-A Nassani, and I.Slama-Belkhodja, “FPGA-based implementation of DTSFC and DTRFC algorithms”, 31st IEEE Annual Conference of Industrial Electronics Society 2005 (IECON 2005), pp.245-250, 6-10 Nov. 2005.

. N.R.N. Idris, C.L. Toh, and E. Elbuluk, “A New Torque and Flux Controller for DTC of Induction Machine”, IEEE Transactions on Industry Application, Vol. 42, No.6, pp. 1358-1366, Nov/Dec 2006.




DOI: http://doi.org/10.12928/telkomnika.v6i3.563

Refbacks

  • There are currently no refbacks.


Creative Commons License
This work is licensed under a Creative Commons Attribution-ShareAlike 4.0 International License.

TELKOMNIKA Telecommunication, Computing, Electronics and Control
ISSN: 1693-6930, e-ISSN: 2302-9293
Universitas Ahmad Dahlan, 4th Campus
Jl. Ringroad Selatan, Kragilan, Tamanan, Banguntapan, Bantul, Yogyakarta, Indonesia 55191
Phone: +62 (274) 563515, 511830, 379418, 371120
Fax: +62 274 564604

View TELKOMNIKA Stats